Structural works are the point at which a building project stops being cosmetic and starts affecting how the building stands up. Take out the wrong wall, form an opening without calculations, or excavate next to a neighbour without notice, and the consequences run from cracked plaster and an awkward conversation to a dangerous structure notice and a stopped site. This guide sets out what structural works actually cover, how to tell whether your project involves them, and the seven checks that keep the job safe, compliant and on programme.

Structural works are any works that alter, remove, support or add to the elements carrying load through a building — walls, beams, columns, floors, roofs and foundations. In practice that usually means:
• Removing load-bearing walls or forming new openings in them
• Installing steel beams, columns and goalpost frames
• Underpinning, foundation strengthening and basement lowering
• Forming or infilling floor openings for stairs and lifts
• Loft conversions, dormers and roof alterations
• Removing chimney breasts
• Facade retention and facade restoration
• Repairs to structural cracking, corroded steelwork or failed lintels
The distinction is not about how disruptive the work looks. Moving a stud partition is messy and non-structural. Cutting a service run deep into a masonry pier looks trivial and is not. If you are unsure, assume it is structural until an engineer tells you otherwise — that assumption costs a survey fee, and the opposite assumption has cost people a building.
• The architect’s drawings note “beam over”, “SE to confirm”, or refer to engineer’s details
• You are changing the use of a space in a way that increases floor loading — storage, plant, gym equipment, archive
• There is diagonal cracking wider than a pound coin’s thickness, doors that stick seasonally, or noticeably sloping floors
• You are opening up a terraced or semi-detached property anywhere near the shared wall
• The building is older than 1950 and nobody can tell you what was done to it in the 1980s

Wall thickness is not proof, and an estate agent’s floorplan is not evidence. Establishing load paths properly means a measured survey, sight of any historic drawings, and opening up where the picture is unclear. Budget for opening up. It is the cheapest money you will spend on the whole package.
A structural engineering inspection establishes the existing condition and load paths; the calculations that follow size the new members and specify the connections. Building control will want to see them, your contractor will price from them, and your insurer will want to know they existed. Getting this done before tender, rather than during, is the single biggest lever on final cost.
Structural works almost always engage the Building Regulations, in particular Part A for structure. You will need either a full plans application or a building notice, and for anything with an engineer’s calculations behind it the full plans route is usually the sensible one. Listed building consent and conservation area restrictions sit on top of this, not instead of it. GOV.UK sets out the building regulations approval process.
Under the Party Wall etc. Act 1996 you must give two months’ notice for works to a party structure and one month for excavation near a neighbouring building or for building at the line of junction. Late notice is the most common avoidable cause of delay on urban structural works, and it is entirely self-inflicted. Serve early, before the programme is fixed. The GOV.UK party wall guidance explains what has to be served and when.
A refurbishment and demolition asbestos survey is a legal requirement before intrusive works in any building constructed before 2000. Alongside it, trace live services, check drainage runs beneath any proposed foundation work, and record what you find. Hidden conditions are the main reason structural works overrun, and most of them are findable in advance.
A small, well-defined package may sit comfortably under a JCT Minor Works contract. A larger refurbishment with sequencing complexity usually needs an Intermediate form. Where the scope is still developing and you would rather design responsibility sits with the contractor, a design and build route can be the better answer. Structural works carry more unknowns than any other package on a refurbishment, so the provisional sums, the contingency and the variation mechanism deserve more attention here than anywhere else in the contract.
Every permanent structural solution has a temporary one holding the building up while it is installed. Needling and propping schemes should be designed, not improvised, and someone should be named as responsible for them. Where there is existing movement, install telltales and monitor before, during and after. Agree hold points so nobody removes a prop on a Friday afternoon because the programme said so.
Under the Construction (Design and Management) Regulations 2015, the client carries duties that cannot be delegated, and on any project with more than one contractor a principal designer and a principal contractor must be appointed in writing. Structural works are high-risk by definition, so this is not a paperwork exercise: the principal contractor controls the site, the sequencing and the temporary works, and the client is expected to have satisfied themselves that whoever holds that role is capable of it. The HSE publishes guidance on CDM 2015 duty holders.
Costs move for predictable reasons: opening up reveals a different arrangement to the one assumed, temporary works turn out to be more involved than the tender allowed, or the making good around the new structure was priced optimistically. The steel itself is rarely the problem.
The practical defence is to price the whole package rather than the headline item — enabling works, propping, the structural element, making good, and the finishes that inevitably follow. A structural works package priced as steel plus labour will always come in over. One priced from an engineer’s drawings with a proper allowance for temporary works and reinstatement usually does not.
Structural works reward the time spent before anyone lifts a tool. Survey properly, engage an engineer early, sort building control and party wall notices before the programme hardens, and put the package under a contract that matches its risk. Do that and the works themselves are usually the straightforward part.
Q10 Consulting advises building owners, developers and housing providers on structural works from feasibility through to completion — survey and inspection, procurement and contract advice, and delivery as main contractor. If you have a project coming up and want a second opinion before you commit, get in touch for an initial conversation.